這張是L相.
這張為N相.漂亮MM請各位高手幫忙看看,電源傳導不過,要如何改進?
電源的輸入為220VAC,輸出為+-15、24、5VDC.傳導在1M前和8M左右均超標,不知道要采用什么措施可以控制,請各位大俠請點一二,非常感謝!這張是L相.
這張為N相.
這張是L相.
這張為N相.全部回復(17)
正序查看
倒序查看
Looks like, this is a switching power supply, the "bad" frequency" from your pic are 160K, 320K and around 640K. They're narrow Band. I guess your primary switching freq is around 80K or 160K. Thus, you need to improve your primary design to kill this low freq spur. Without Schematic, I don't know how to improve it.As far as the 8MHz, it is wide band, try to use a larger common choke at AC input side, and see if it works.
0
回復
@xiang_97124
Lookslike,thisisaswitchingpowersupply,the"bad"frequency"fromyourpicare160K,320Kandaround640K.They'renarrowBand.Iguessyourprimaryswitchingfreqisaround80Kor160K.Thus,youneedtoimproveyourprimarydesigntokillthislowfreqspur.WithoutSchematic,Idon'tknowhowtoimproveit.Asfarasthe8MHz,itiswideband,trytousealargercommonchokeatACinputside,andseeifitworks.
謝謝高手指點,我先試試.非常感謝!
0
回復
看你的電壓騷擾測試結果,除共模外,差模也成問題,如果從這張表數據看你需要加一個差模電感,電感量大約是你變壓器原邊電感量的1/20(鐵粉芯材料) 和一個0.1~0.47u/630v的CBB20或CBB21的薄膜電容,如果你的開關電源是采用的功率開關器件且散熱器是接保護地(PE)的,那么需要你再加一個共模扼流圈和兩個濾共模干擾的Y電容2200P~4700P/250V AC.當然以上是常規設計.如果你想節約成本,可把你的電路傳給我,我會幫你看看有沒有低成本的EMC處理方案.
0
回復
@rojes
看你的電壓騷擾測試結果,除共模外,差模也成問題,如果從這張表數據看你需要加一個差模電感,電感量大約是你變壓器原邊電感量的1/20(鐵粉芯材料)和一個0.1~0.47u/630v的CBB20或CBB21的薄膜電容,如果你的開關電源是采用的功率開關器件且散熱器是接保護地(PE)的,那么需要你再加一個共模扼流圈和兩個濾共模干擾的Y電容2200P~4700P/250VAC.當然以上是常規設計.如果你想節約成本,可把你的電路傳給我,我會幫你看看有沒有低成本的EMC處理方案.
謝謝這位大哥,呵...我先試試看,如果再不行,就傳給你幫我看看!
0
回復
