大家好:
請問電解的損耗角正切值代表什么性能.比如說正常的2.2μF400V 5000小時一般廠家定義的為0.10,有的定義為0.20.是隨機定義的么?一般的測試不超過0.08,為什么標的如此高.
電解耐久實驗的測試條件不一樣,一種為105度,施加額定電壓及額定紋波電流5000H .一種是105度,施加最大紋波電流及額定電壓,然后回復常溫條件測試.假設兩種產品的容量變化,損耗角正切,漏電流一樣.是不是試驗過程中施加最大紋波電流的產品性能更可靠.
另:漏電流代表什么參數性能.
一般的電解電容都是采用100HZ或者120HZ測試的容量和損耗.為什么大多數公司的樣本上都是120HZ,不同頻率會有什么影響.
請幫忙回復相關問題
全部回復(10)
正序查看
倒序查看
@czd195218
哈哈,還沒有很貼切的?老兄不能直接告知么?還有一個問題,2.2μf400v普通手動測試條件下漏電流怎么算?
不同的生產廠家其LC可能會不一樣的計算.(其SPEC上一定會標示出來的,可參考供應商的規格書)
一般的其計算公式如下:
Leakage current(uA):KCV or 3uA or less(注:不同系列,不同規格的其系數不一致,K為常規系數--可變化 如:0.01CV,0.02CV C:電容容量,V:標稱耐壓值)
一般的其計算公式如下:
Leakage current(uA):KCV or 3uA or less(注:不同系列,不同規格的其系數不一致,K為常規系數--可變化 如:0.01CV,0.02CV C:電容容量,V:標稱耐壓值)
0
回復
Tangent of loss angle or dissipation factor :
1)The tan is the ratio of the resistive component(ESR)to the capacitive reactance(1/wc)in the equivalent series circuit,
and its measuring conditions are the same as the capacitance.
2)The tan show higher values as a measuring frequency increases and a measuring temperature decreases.
3)Leakage current:The dielectric of a capacitor has a very high resistance which prevents the flow of DC current.however,due to the characteristics of the aluminum oxide layer that functions as a dielectric in contact with electrolyte,a small amount of current,called leakage current,will flow to reform and repair the oxide layer while a volgage is being applied.
Thank for you question.
1)The tan is the ratio of the resistive component(ESR)to the capacitive reactance(1/wc)in the equivalent series circuit,
and its measuring conditions are the same as the capacitance.
2)The tan show higher values as a measuring frequency increases and a measuring temperature decreases.
3)Leakage current:The dielectric of a capacitor has a very high resistance which prevents the flow of DC current.however,due to the characteristics of the aluminum oxide layer that functions as a dielectric in contact with electrolyte,a small amount of current,called leakage current,will flow to reform and repair the oxide layer while a volgage is being applied.
Thank for you question.
0
回復
@青春之歌
Tangentoflossangleordissipationfactor:1)Thetanistheratiooftheresistivecomponent(ESR)tothecapacitivereactance(1/wc)intheequivalentseriescircuit,anditsmeasuringconditionsarethesameasthecapacitance.2)Thetanshowhighervaluesasameasuringfrequencyincreasesandameasuringtemperaturedecreases.3)Leakagecurrent:ThedielectricofacapacitorhasaveryhighresistancewhichpreventstheflowofDCcurrent.however,duetothecharacteristicsofthealuminumoxidelayerthatfunctionsasadielectricincontactwithelectrolyte,asmallamountofcurrent,calledleakagecurrent,willflowtoreformandrepairtheoxidelayerwhileavolgageisbeingapplied. Thankforyouquestion.
第三條.我是這么翻譯的,感覺不順暢,請指點什么意思!
漏電流:非導電性的一個電容器有防止DC current.however的流動的一種高的抵抗,由于特性鋁氧化物層起的作用一非導電性與少量電流,電解液接觸,當volgage被使用時,叫漏電流,將流改革并且修理氧化物層
漏電流:非導電性的一個電容器有防止DC current.however的流動的一種高的抵抗,由于特性鋁氧化物層起的作用一非導電性與少量電流,電解液接觸,當volgage被使用時,叫漏電流,將流改革并且修理氧化物層
0
回復
